dognovel Chapter 594 The Posture Of The Protagonist (Kneeling To Subscribe)
Chapter 594 The Posture Of The Protagonist (Kneeling To Subscribe)
Chapter 594 The Posture of the Protagonist (Please beg to subscribe)
"I went to the chip workshop to have a look. Just now, I adjusted the rotation speed of the machine tool in the finished product workshop."
"How much did you adjust?"
Tiedan heard Qin Yan say that he adjusted the rotation speed of the machine tool and hurriedly asked.
Why didn't Qin Yan inform himself of such a big matter, he was a bit puzzled.
"On the basis of the original, the number of revolutions has been increased by three percent.
Qin Yan said lightly.
Tie Dan couldn't calm down after hearing this, and he hurriedly said: "No, the speed of the finished product workshop has already reached 30,000 revolutions per second, if it increases by 30%, wouldn't that kill the machine tool?
"Let me calculate, it's okay, trust me."
"27 When I entered the gate of the factory, the assistant stationed in Bali reported to me the sales situation in Bali.
"The mobile phones put into the Bali market were sold out in one morning.
"It must be replenished tomorrow."
Qin Yan took Tie Dan's words and said.
He has confidence in himself, more confidence in the system, and believes that the system will not cheat him.
I was apprehensive before, but now I am calm.
For tomorrow's replenishment, are you going to take risks?"
Tie Dan asked puzzledly, his tone showed a little distrust, and the eyes of an insider looking at an outsider.
It's already very unfriendly to look at him.
"Don't look at me with that look, I'm scared."
"Don't forget, I am the person who designs and produces mobile phone machine tools. I know the limits of machine tools better than you. The internal structure of alloy steel can withstand the test of high speed."
Only then did Qin Yan know that Tie Dan is caring, and caring for machine tools is like caring for one's own eyes.
While he was grateful to Tie Dan, he also felt that increasing the rotation speed of the machine tool had to pass both his own level and Tie Dan's level.
"Replenishment is very important, and it can't be at the cost of destroying the machine tool. I won't tell you. Go to the finished product workshop and have a look."
Tie Dan felt that it was superfluous to say anything to Qin Yan, so he had to visit the finished product workshop to make sure of it.
For the first time, he was rude to Qin Yan, his eyes were full of hostility.
Forgot, even though I am the director of the factory [Dong Lihuang is a high-level wage earner. He was hired by Qin Chuan.
Tie Dan forgot everything, and hurriedly opened the door of the finished product workshop with the attitude of the master.
He listened to the sound of the machine turning, listened to the subtle sound of the finished product rolling down, and then looked at the big crane, which was constantly lifting the packing box and putting it into the container.
A hanging heart just fell, and suddenly hung up again.
He was worried about his eyes and ears, and could not let Qin Yan's willfulness destroy these machine tools and also the factory.
Tiedan took out the detector to test the machine tool, and check the load rate of the machine tool and the limit of fatigue.
...253...
The detector was working, and Tie Dan's heart was beating wildly. Now it had jumped to the throat, and it was only a few centimeters before it jumped out of the mouth.
Qin Yan did not follow Tie Dan back to the finished product workshop. He didn't know why Tie Dan went to the finished product workshop?
Turn down the RPM?
Tie Dan couldn't do it. With the help of the system, he built a protection system. Without his own fingerprint input, no one can change the number of revolutions.
He has confidence in himself, and he doesn't dare to mess around with Tie Dan, so he has a hundred hearts.
Qin Yan pushed open the door of the chip synthesis workshop.
He walked in like the wind.
Standing in front of the machine tool, looking at the number of revolutions of the machine tool, he nodded, the number of revolutions of the machine tool is okay. .